Autonomous water supply for a private house: water sources, diagrams and materials

Without a clear idea of ​​how to properly organize the supply of water to the house, the risk of shortcomings and subsequent inconveniences increases significantly. This may entail not only unnecessary financial costs, but also subsequent maintenance of the system.

In this article we tell you how to properly supply water to a private home and how to save on equipment without harming the performance of the system:

• Where to place the water inlet
• Installation of a water supply entry point into the house
• What pipes to use for water supply
• How to properly dig a trench with your own hands
• Diagram of pipeline entry into a private house down to each fitting
• Insulation of pipes at the entrance to the house
• Do I need a heating cable and which one is better to use?
• Unobvious mistakes when laying pipes
• How to order water supply to your home and how much it costs

Correct location of water supply to the house

In the vast majority of cases, water in a private house is supplied from three sources: a well, a well and a central water supply. In this case, the passage unit of the foundation and floor does not change significantly, but what immediately follows it changes: with a central water supply, an automation unit and a hydraulic tank are not required, but one of the frequent requirements is the installation of a meter.

There are two methods for constructing a well: with a caisson and with a well adapter. If there is no bathhouse or garage on the property, and you do not plan to share water with your neighbors, then an adapter is an ideal option. You can read more about the advantages of the adapter in this article. When considering the question of where to install water supply in the house, you need to take into account where the hydraulic tank, pressure and dry running switch will be located, if necessary, and you should also not forget about water filtration and water treatment. When constructing a well with a caisson, automation and filters can be placed in it.

If you want a well, then there are 2 options for how to bring water into the house: if there are space restrictions, then it is better to install pumps with built-in automation. Grundfos SBA or Dab Divertron well pumps are perfect for this. If your house has a separate technical room, then you can consider the option of a pumping station. However, it should be taken into account that the difference between the station and the water level in the well should not exceed 8 m.

Typically the entry is made near the wall. The input unit (conditionally this can include a filter, a pressure switch, a dry-running relay, a half-faucet outlet to the street, a hydraulic accumulator) occupies a width of about 0.5 meters on the wall.

Advice! At the design stage of your residential building, make room for the boiler room. In the technical room you can place equipment, carry out all communications, and also eliminate the noise of the pumping station.

Decide in advance on the location of the well or well on the site in order to minimize the distance from the water supply source to the entrance to the house. This will not only reduce the amount of excavation work, but will also make it possible to understand in which direction to lay the foundation in the foundation.

Rules for connecting a private house to the central water supply

Scheme of connecting a house to a water supply system

To bring water from the central water supply to the site with your own hands, you must comply with certain conditions. They are regulated by government decree No. 644 dated July 29, 2013. Basic rules regulated by the regulation:

• drawing up an approved contract according to the existing scheme;
• availability of an application for connection, which is submitted to the territorial authorities - the application is considered within 5 days;
• obtaining technical conditions for insertion into the water supply system, which must be strictly observed;
• after receiving the documents, the service checks them within 3 days, determines the balance of drainage and water supply, and technical feasibility;
• if there are incorrectly executed or incomplete documents, the customer receives a notification; within 20 days he must collect and send the missing information;
• if this does not happen after 20 days, the application is canceled.

If everything is done correctly, the territorial government service issues a permit. Vodokanal draws up an agreement within 20 days and sends it to the customer. It specifies the conditions, cost of work and payment.

Plumbing services, by law, cannot refuse the customer to draw up a contract if technically possible. If this is not possible, an individual project is created.

Payment is made as follows: 35% within 15 days after drawing up the contract, 50% within 3 months from the start of work, but not after its completion, and another 15% within 15 days after signing the final acts confirming the guarantee of water supply to the house.

Introducing water supply into a house under the foundation

It is necessary to think in advance, at the design stage, about the location of technical holes in the foundation. Typically, such holes are needed for the following:

• water supply
• sewerage
• for electricity
• backup

Sooner or later you will need a reserve hole to provide household amenities: for example, the outlet of a water supply pipe for a newly built bathhouse or garage, for the outlet of an external lighting cable. An additional hole will slightly increase the cost of the entire job, but will significantly save time and effort in the future.

If you do not take into account the location of technical openings for communications in advance, then the builders will do this at their own discretion. As a result of this, the node may be located not near the wall, but, for example, in the middle of the room. Not only is this inconvenient, but in the future it will require additional financial and physical costs to redo everything.

To prevent this from happening, it is necessary to mark the location of technical holes at the design stage, taking into account the width of the walls, including the interior decoration.

Dependence of the pipeline input device on the type of foundation

Slab foundation

An embedded pipe with a diameter of 110 mm must be installed under the water supply inlet. Usually a sewer pipe for external work (red) under the 32nd HDPE pipe is used. Accordingly, this should be taken care of in advance. The pipe must be removed from under the foundation at a depth of about 1.5 m - this value is relevant for the Leningrad and Moscow regions, depending on the region. Below we will tell you how to determine the laying depth for your region.

Strip foundation

Strip foundations can be divided into 2 types:

• Non-recessed (shallow) strip foundation

  . In this case, it is not necessary to lay the sleeve in advance, since it is possible to dig under such a foundation. However, a sleeve under the tape will still be required, since the foundation may damage the water pipe during settlement.

• Recessed strip foundation

  . If this type of foundation is located below the frost depth, then it is better to install the mortgage before pouring. For this you can use a sewer pipe with a diameter of 110 mm. If the pipe is not laid, then diamond drilling of this hole in the foundation will be required in the future, for which you need to call a specialist. His work will cost you an additional 6,000 rubles.

Advice! Always leave access to the underground for the strip foundation and a height of at least 40 cm from the ground to the subfloor. In case of an emergency, you can climb into the basement and work there. In this case, the sewerage installation can also be done under the floor on a suspension.

Foundation on screw or reinforced concrete piles

A columnar foundation can also be included in this category. Most often used for frame houses or houses made of timber. At the construction stage, we recommend laying a 50 mm pipe for the water supply.

Entrance to the ground floor

One of the most difficult options, provided that groundwater passes close by. If the pipe fits below the freezing depth, then the pipe does not need to be buried or insulated. In this case, the input must be waterproofed. This requires insulation for the input of communications. It has a special composition that does not lose its tightness when the foundation and pipes move (and they will definitely happen). The solution is elastic and has good adhesion to both concrete and plastic.

Waterproofing foundation passages is a separate and broad topic, we will talk about it in the following articles. It is worth mentioning separately that, based on our experience, it is better to use sealant for cable glands, FST-250 or VBH SS-11. The second option is to combine bentonite cord with a non-shrinking solution.

Thus, simply sealing the inputs with polyurethane foam will not work. Waterproofing must be taken seriously and all manufacturer's instructions must be followed. Otherwise, even a small leak will flood the basement of the house along with all the equipment that will be installed there.

We strongly recommend calling one of our MEP specialists before pouring your foundation slab. With an engineer, you will be able to make the necessary calculations: the location of the well, at what depth, and in which direction to lay the embedded pipes, as well as the most competent placement of water supply and sewerage systems (septic tank) on the site.

Decentralized water supply

If you are planning to switch to a decentralized water supply, take into account the properties of the soil, the depth and condition of the internal waters. And also be prepared to install pumping equipment and filters for water purification.

IMPORTANT! There is no need to pay for using an autonomous system, but pumping equipment and the construction of a well or well are expensive.

Tips for choosing a location for water intake structures:

1. It must be installed at a distance of 20-30 meters from treatment systems, compost pits and other potential sources of pollution.
2. The area must be free of flooding.
3. There should be a special blind area around the well or well (no narrower than 2 meters). The surface part should be 80 cm from the ground, covered with a lid on top.

Features of water supply from a well

Water from a well
There are two types of wells for home water supply:

1. Well "on sand".

• Depth from 15 to 40-50 m, service life - from 8 to 20 years.
• If the aquifer is shallow, you can drill it manually.
• To supply water, you will need to install pumping equipment and filters.

1. Artesian well.

• Depth up to 150 m, service life – up to 50 years.
• Only special equipment drills.
• Water rises on its own due to its own pressure.
• Pumps are used for transportation only.
• Such a well is registered and a passport is issued for it.

Well advantages:

• stable volume of water;
• high water quality;
• no need for regular repairs.

Disadvantages of a well:

• drilling is an expensive procedure;
• service life is shorter than that of a well;
• additional expensive pumps must be used.

Most often, wells consist of a mouth and an above-ground part. The mouth is constructed in an underground chamber - a caisson. The water intake device also has a barrel. Its walls are reinforced with steel casing pipes. and the water intake part (consists of a settling tank and a filter).

Well for water supply

This is the simplest solution for autonomous water supply if the aquifer is powerful and located at a level of 4-15 m.

Water supply from a well

Most often, a well is constructed from concrete rings or bricks. It consists of an above-ground part with an exposed ventilation pipe, a trunk, a water intake and a water-containing part.

Water enters the well through the bottom or walls. In the first case, a gravel bottom filter is placed on the bottom for additional water purification.

If water enters through the walls, special “windows” are made and gravel is poured into them, which also serves as a filter.

Pros of the well:

• easy to build;
• you can manually raise the water if the electricity is turned off;
• low cost of pumps;
• serve for a long time - more than 50 years.

Disadvantages of a well:

• Water quality: groundwater with particles of earth and silt can penetrate there.
• To prevent water from overflowing, the well must be cleaned regularly.
• Water levels vary depending on the time of year, so in hot weather shallow springs may dry up.

You can build a well with your own hands; for this you will need reinforced concrete rings, a tripod with a winch, buckets and shovels. The well is easy to maintain and access to the water source is convenient.

The option with a well is suitable in the following cases:

• if the level of water consumption among the residents of the house is low;
• there is a powerful protected source with good water;
• if there are no other options.

Sequence in organizing a water supply system

When arranging the water supply at home, you need to follow a certain sequence. After the water source is ready, install:

• external and internal pipeline;
• pumping and additional equipment;
• filters for water purification;
• distribution manifold;
• water heating device.

At the end, plumbing fixtures are connected.

What pipes should be used to bring water into the house?

Pipes with a diameter of 32 mm HDPE (low-density polyethylene) - according to GOST, are marked with a blue stripe and this means that they are for use under water, excellent for small country houses. For large cottages we use pipes with a diameter of 40 mm. However, if central water supply is used, the administration may impose its own restrictions on the diameter of the pipes, for example up to 25 mm.

To connect pipes, we most often use compression brass fittings for HDPE pipes Tiemme or Itap: they look more aesthetically pleasing and are more reliable than plastic ones. Unlike, for example, electric welded fittings, these fittings can be installed manually, with minimal use of tools. They can also be used indoors or in summer water supply. Plastic fittings are not suitable for heavy loads. Using them to secure pipes that are buried to great depths—and especially a pump—is out of the question.

Conclusion and useful video on the topic

Having decided to independently install a water supply system in a private house, you need to realize that the process is quite complex and has a number of features. It's better when the work is done by professionals. Water from an artesian well has better quality characteristics, as it is suitable for drinking. But if you need it for irrigation or technical needs, you don’t have to spend money, and a well is enough.

When designing, it is necessary to take into account the pipe material, the performance of the pumping station, the depth of groundwater and other parameters. Otherwise, if you have construction skills and tools, you can assemble the pipeline yourself. Everything is decided by the needs, capabilities and wishes of the homeowner.

Insulation of pipes at the water supply to a private house

We insulate pipes using insulation and heating cable. We install the food grade heating cable inside the pipe because it is quite easy to replace. With this installation, the cable transfers 100% of the heat to the water and does not heat the air around it. Insulation will help you use a heating cable of lower power, for example, 10 W, and save on electricity.

Heating cables are resistive and self-regulating.

• Resistive

  - have constant power along the entire length. At the point of overlap, the cable overheats, which causes rapid wear and destruction.

• Self-regulating

  — its temperature does not exceed 65°C, which eliminates overheating. As a result, it is fireproof and more wear-resistant. For the same reason, it can be installed overlapping, and this will not cause local overheating.

The cable is selected according to power. As a rule, 16 W/m is quite enough for HDPE pipes with a diameter of 16 to 32 millimeters when installed outside. If the cross-section of the pipe exceeds 32 millimeters, then you should choose a cable with a power of 24 W/m. We, in turn, use and install about 3 meters of food cable with a power of 10 or 13 W.

It should also be noted that a self-regulating heating cable does not require an additional thermostat, unlike its resistive counterpart. It is quite simple to install and plug into a power outlet.

To install the cable, you will need a tee (we use a 90° tee), which is installed on the pipe in the house.
The cable enters it from above. Set of heating food cable for laying inside a pipe with a water gland, 3 m.
For additional insulation of the pipe, we use 2 layers of 13 mm thermal insulation made of foamed polyethylene. We use 4 whips of 2 meters with a diameter of 34 and 54 mm. Foam insulation is relatively inexpensive, so you will not feel any special financial costs.

Thermal insulation of foamed polyethylene pipes

Material selection

After receiving all permits, you can select and purchase the necessary material. In addition to the pipes themselves, you will need insulation, a meter, faucets and other shut-off valves.

The most important element of the future water supply system of a private house can be considered pipes. The selection of such products is quite large. You can purchase pipes from the following materials:

• Steel. Such products quite recently were almost the only option for creating a plumbing system. The material is durable and not afraid of mechanical stress. But such products rust and are difficult to install;
• Copper. Such pipes are rarely used. Copper is an expensive material and difficult to install. In addition, such pipes cannot be laid in the ground. But copper pipes in a house will last for decades;
• Plastic. This material is used almost everywhere today. Plastic is inexpensive, easy to install, durable and not afraid of aggressive environments.

When choosing pipes for the water supply of a private house, one should not forget about such characteristics as diameter. The pressure in your system will depend on this parameter. Here a lot will depend on the operating pressure and the cross-section of the pipes in the central water supply. In this regard, it is better to get advice from water utility specialists.

Diagram of the water supply unit to the house

A similar scheme is used by our company in most cases when supplying water to a private house from a well or from a well with a submersible pump.

Designations:

1. Insulation 34 mm
2. Insulation 54 mm
3. cable tie
4. HDPE pipe 32 mm
5. Fitting 32/1" HP
6. Brass tee 1"
7. Brass fitting 1”-½”
8. Pump cable
9. Self-regulating heating cable kit (supplied with gland)
10. 1” fitting with transition to pipe. Inside the house, we switch to polypropylene or metal-plastic pipes.
11. Watering tap outlet (installed before the filter)
12. Oblique filter (dirt filter)
13. Fine filter (retains particles from 5 to 25 microns)
14. Dry running relay (if the pressure drops below 0.5 bar, it turns off)
15. Five way connector
16. Pressure gauge
17. Hydraulic accumulator
18. Tap leading into the system

We use HDPE pipes 32 mm (4) with seals 54 mm (1) and 34 mm (2). We install the fitting - transition from 32 mm HDPE to 1” external thread (MS) (5). Next, install a 1” brass tee with internal thread. We screw a 1”-½” fitting into the tee from above. And then we screw in the sealed lead-in to insert the heating cable inside (8). We seal all connections (we use only flax with sealing paste).

Next comes a set of self-regulating heating cable (8), which is inserted inside the pipe along with a special seal (gland, included with the cable).

Install the outlet of the watering tap (11). Since it does not require much filtering of water, we install it before the filters. There are 2 taps installed on it: 1 with a fitting outside, the other inside the room. In winter, the tap is turned off inside the house, and the outside one remains open to drain the water (the pipe is laid through the wall at an angle).

Then we install an oblique filter, or mud filter (12). It can be placed before the watering tap - it doesn’t matter.

Fine filter (13) - retains small particles from 5 to 25 microns. Needed for protection against fine sand and is installed optionally. Dry running relay (14), to which the cable from the pump (8) is connected. If the pressure is below 0.5 atmospheres, the relay turns off, after which it can only be turned on manually. This helps protect the pump from running dry if for some reason the water does not have time to fill the well (for example, seasonal changes in the well's flow rate). Dry operation for the pump is dangerous due to overheating, since it is cooled by transient liquid.

We do not use a dry-running relay when supplying water from a well, since well pumps are equipped with built-in automation with appropriate protection (as in Dab Divertron) or a float level sensor (Grundfos SBA and Belamos KF). Five-way connector (16) on which the pressure switch is installed and pressure gauge (15). It also comes with a connection to the hydraulic accumulator (17).

The valve in the system (18) is installed strictly after the automation. What usually happens: Somewhere in the house a faucet turns on. The pressure gauge records the pressure drop in the tank, after which the pump turns on to supply water. If the valve (18), installed incorrectly, is closed, then a water hammer will occur, which will disable the entire system, and the pump will simply burn out.

Also, do not forget that in addition to the water pipe, an electric cable is brought into the house from the pump in the HDPE pipe.

Scheme of water supply for a private house from a well with a hydraulic accumulator

This system is similar to the previous one. It consists of a water intake point, a supply pipe, a hydraulic accumulator and internal wiring. However, there are some differences. To protect against freezing, the wellhead is often equipped with a plastic or steel caisson. It is also possible to install a hydraulic accumulator in it (if the well is located near the house). In this case, the pumps are submersible (it is better to choose models with built-in protection against idling).

Modern water supply schemes from a well necessarily contain an automation kit. It allows you to adjust and monitor the operation of the water intake unit.

The minimum set will include:

1. Pressure switch with pressure gauge - maintains the required pressure in the accumulator.
2. Float-type switch - stops the supply of electricity to the pump if the well becomes shallow.
3. Dry running protection – turns off the motor if there is no water in the pump.

Automation is available in several varieties on the market. For self-installation, it is more convenient to use first-generation devices, as they are the simplest and most affordable. A practical diagram of water supply to a house from a well with a hydraulic accumulator is shown in the photo below.

How to make a water pipe with your own hands?

You can assemble your own water supply according to our diagrams. To do this you will need tools:

Equipment you will need for self-installation

Construction hairdryer.

If you have a well or well with a caisson, the cable from the pump is extended using a heat-shrink sleeve. In order for shrinkage to occur successfully and the connection to protect the contacts from water, the coupling is heated with a hair dryer.

T-shaped installation key.

Screws into adapter with connected pump. The cost is about 1000 rubles. You can also make the key yourself from metal or polypropylene pipes.

Set of bimetallic crowns.

Diameter - up to 44 mm. Needed for the hole when installing the downhole adapter. And also for drilling holes in ceilings and walls, including at the entrance to the house. Twist drills can be used for these purposes.

Soldering iron

Or an “iron” for soldering polypropylene pipes. The average cost is about 3,000 rubles. Soldering tips are consumables and need to be changed periodically because the Teflon coating peels off.

Advice! Consider how long it takes to heat the pipe: there are special tables on the Internet. Overheating is dangerous because the melt closes the internal passage of the pipe. Underheating threatens weak adhesion and poor pipe connections.

Press jaws.

Press fittings are installed on metal-plastic pipes using special pliers. Unlike compression fittings, such connections are non-separable, but more reliable: such connectors can be poured into the screed and used for hidden installation, for example in floors. But we recommend installing a pipeline with compression fittings in plain sight, because the nuts need to be tightened regularly. Press pliers can be manual or electric. Power tools are more expensive, but they do all the work for you. For small installations, a hand press is sufficient. Manual press pliers cost from 6,000 rubles. Electric - about 50,000 rubles.

Adjustable wrench for fitting fittings.

"Swede".

With the help of a “swedge” you can grab and hold pipes and fittings that do not have turnkey surfaces.

Sealant.

Necessary for sealing threaded connections. Beginners often have a question: what is the best way to seal threaded connections? Now there are many options: fum tape, glue-sealant, and flax with paste.

Advice! We recommend using plumbing flax or paste (simply putty), for example, from Unipak. We strictly do not recommend using fum tape or any other analogues.

Circuits and equipment for hot water supply

What equipment is needed to provide a home with hot water? Here is a description of the most popular solutions.

Electric boiler

Device: heat-insulated tank with heating element and thermostat.

Boiler design elements

Advantages:

• Light load on the wiring (the power of the heating elements is in the range of 1-3 kilowatts);
• Stable water temperature;
• Possibility of precise temperature control.

The thermostat allows you to set and maintain water temperature

Flaws:

• High cost per kilowatt-hour of heat;

Captain Obviousness suggests: all electric heating devices have an efficiency of 100% (minus heat loss through the body). To get a kilowatt-hour of heat, you need to spend exactly the same amount of electricity.

• Heat loss through the thermal insulation of the tank: the boiler periodically turns on the heating elements to heat water even in the absence of its consumption;
• Energy dependence. If your lights are turned off, hot water will quickly run out.

Connection: the boiler input is fed from the cold water supply, the output is connected to the hot water distribution. A safety group consisting of non-return and safety valves is installed at the entrance. The check valve prevents the draining of heated water when the hot water supply is turned off, and the safety valve prevents a dangerous increase in pressure in the tank and water supply due to thermal expansion of water.

Electric boiler connection diagram

Indirect heating boiler

Device: thermally insulated tank with a heat exchanger and pipes for connection to cold water, hot water and heating systems.

Indirect heating boiler heat exchanger

Advantages: connects to any type of heating boiler. Allows for energy-independent (without the use of electricity) preparation of hot water. The cost of a kilowatt-hour of heat is determined only by the type of fuel used.

Connection:

• A small-volume indirect boiler is connected to the water supply in the same way as an electric boiler;
• For volumes above 150 liters, the safety valve is replaced with an expansion tank. It also solves the problem of thermal expansion of water, but in a different way: it does not discharge water into the drainage, but stores its excess by compressing air;

Expansion tank in indirect piping

• The boiler is connected to the heating system in parallel with the heating circuit. During the warm season, the batteries are turned off and the coolant circulates between the heat exchangers of the boiler and boiler.

Gas water heater, double-circuit boiler

Device: geyser - instantaneous water heater that uses the combustion heat of gas. Its supply is regulated by a thermostat - mechanical or electrical.

A double-circuit boiler combines heating with the preparation of hot water in an additional heat exchanger (separate or coaxial).

Boiler installation for heating and hot water supply

Advantages:

• Using the cheapest heat source - main gas;
• Compactness of the water heater;
• Models with piezo ignition and a mechanical thermostat are energy independent.

Disadvantage: low accuracy of temperature control for devices with a mechanical thermostat. Trying to take a warm shower becomes a constant battle with the faucet taps.

Connection: into the gap between the hot and cold water pipes. The only additional fittings that can be installed are taps that cut off the column or boiler, and a mechanical filter on the inlet pipe.

However: if there is a filter at the water supply inlet, the make-up water does not require additional purification.

The column is connected to cold water and hot water supply systems without additional fittings

We dig a trench to bring water into the house with our own hands

According to SP 22.13330.2011, for Moscow and the Moscow region the freezing depth for clay and loam is 1.1 m, and for fine sand and sandy loam - 1.34 m. For St. Petersburg and the Leningrad region - 1.0 m and 1.2 m, respectively.

In the middle zone of the Moscow and Leningrad regions, the depth of the trench ranges from 60 to 150 centimeters - depending on the depth of soil freezing (we always lay the pipe below the freezing depth!). At the same time, we do not consider the territories of our country with permafrost. The summer water supply option is 30 - 40 centimeters.

The width of the trench must be at least 30 centimeters. This is necessary for the convenience of laying the pipe, so that a person with an ordinary build can fit in the trench and be able to work in it.

We do not recommend skimping on trench depth. At the optimal pipe depth (about 1.5 meters), we use about 3 meters of heating cable per input. In rare cases, we can use a cable length of up to 6 meters: usually when the pipe entry is not made at the outer wall, but at a distance from it. Thus, this length will be enough for us to warm up the water at the pipe exit from the house (if the house is on stilts or on a strip foundation, then approximately 0.5 meters), as well as at a smooth exit to a depth below the freezing level (about 2 meters).

However, if the depth of the trench is higher than the freezing depth, then the heating cable will have to be laid along the entire length of the pipe, and this, in turn, is quite expensive: the cost of the cable, the cost of electricity. Also, when the cable becomes unusable, and to replace it you will have to dig out the entire trench.

For our clients, we always dig below the freezing depth, and use a heating cable to heat only the area where the pipeline enters the house.

Water sources

Water supply to the house can be organized:

1. From the well . The obvious advantage of this solution is its low cost and the ability to implement the project with your own hands from start to finish (see Water supply from a well: how to do it right). An equally obvious disadvantage is that water of drinking quality is quite rare in the upper aquifers;

Well made of KS rings

1. From the well . Lower aquifers typically provide water with minimal contamination. Alas, drilling a well is an expensive undertaking (drilling a linear meter of its shaft costs from 2 to 4 thousand rubles, depending on the type of soil);

water well

1. From the container. The tank can be filled with imported water or a country water supply with water supplied according to a schedule. The latter scheme is typical of many garden cooperatives in warm regions of the country.

Connection to summer water supply

Three non-obvious mistakes when laying a water pipe and introducing it into the house

Often, home owners are faced with the fact that the water supply unit is skewed, which can cause a pipe collapse.

This can happen for several reasons:

The trench was dug incorrectly.

This usually happens if the entrance to the foundation is made at a right angle. The pipe must be placed on solid ground. The trench must rise smoothly (there must be a slope) so that the turning radius is sufficient and the pipe does not break. Also, the soil sags over time, the pipe goes down and pulls the assembly along with it, breaking it out of the connection, both in the house and at the well adapter, caisson, at the well.

Right angle in the mortgage.

Typical mistake: builders, when pouring a foundation (monolithic slab), install an embedded pipe with a diameter of 110 mm and move from the vertical section to the horizontal section at an angle of 87°. In this case, we make a smooth turn from the vertical section, for which we use 2 angles of 45°, or 3 angles of 30°. The same smooth turn should be used when installing a sewer outlet - at least 2 bends at 45°. If you try to insert the HDPE pipe at a right angle, it will break.

If such a mistake has already been made, then there are 2 options.

pass a corrugated stainless steel pipe, such as Neptun, through such an outlet. They are expensive - a 32 mm pipe costs about 400-500 rubles per linear meter, plus the cost of fittings.

If the mortgage is located near the outer wall of the house, you can dig under the foundation and redo the incorrectly made mortgage.

The pipe is laid incorrectly.

The pipe must be laid in such a way that due to linear expansion it does not lose its tightness and does not damage the connections. To do this, our specialists lay the HDPE pipe in a “snake” pattern, thereby leaving a margin for the contraction and expansion of materials when the temperature changes.

Case from practice. The usual situation: laying takes place in the summer. Black HDPE pipe heats up in the sun. It is laid out on the bottom of the trench in one line and quickly covered with soil. The pipe in the ground cools and narrows.

There is no need to sprinkle HDPE pipes with sand throughout the entire laying, as many advise. Nothing bad will happen, it's just extra costs.

It is clearly visible that the pipe is being pulled down. The reason is soil subsidence near the input .

The nuances with which DHW is supplied

Typically, electric or gas boilers, water heaters or boilers are purchased for this purpose. The equipment can operate on solid, liquid fuel or gas. Each option has its own advantages and disadvantages; it is worth focusing on what is most often chosen in the region.