Having your own hot tub used to be a luxury, but today even a person with an average income can afford to buy a hot tub. If you are planning to build a country house or renovate an apartment, then be sure to think about buying a similar plumbing product. Thanks to the jacuzzi, you can relieve stress, relax and unwind, and - and this is important - with health benefits. But the matter does not end with the purchase of a jacuzzi, because it must be installed and connected correctly. This, of course, can be done by specialists, but in reality the work is not complicated and you can easily handle it yourself. You just need to approach the matter wisely.
DIY installation and connection of a jacuzzi
Connecting the hot tub to the sewer system
To connect a hot tub to sewer lines, a drain with a hole diameter of 4-5 cm is used. It is convenient if the sewer pipe is located in the floor or wall. In the latter case, the distance from the floor should not be more than two centimeters.
At the final stage, the siphon from the jacuzzi is connected to the drain with a corrugated pipe. After connecting the bath to the communications, it is necessary to check all connections for leaks. To do this, fill the bowl with water and carefully inspect the joints. Then you need to seal the junction of the jacuzzi to the walls. The water from the bowl is drained only after the sealant has hardened.
Algorithm for installing a hydromassage mechanism
Installation of a whirlpool bath begins with the manufacture of a rectangular frame. It will be located at the bottom, and it should be tightly fixed in a stationary position. Next you need to install the tee. After that, holes are made in the tubes, the interval between holes is 100 mm. The diameter of the holes is 1.5 mm. They should be directed from the bottom, to where the person lies. A plastic hose is attached to the tee. The second end of the hose is connected to the vacuum cleaner, which serves to supply air.
Hydromassage bath
Installing a hot tub from an official Jacuzzi service center - what could be more prudent?
The real queen of all baths is undoubtedly the Jacuzzi. Immerse yourself in a relaxing, warm bath bubbling with thousands of bubbles - what could be better after a working day? We install a Jacuzzi from a leading global manufacturer. Jacuzzi hydromassage baths have dozens of different types of hydromassage and sets of systems. Adjustable pressure, air massage, heating system, underwater lighting - you can choose any set of functions. And numerous shapes, colors and designs allow you to install a Jacuzzi in full accordance with the interior of your bathroom.
Installation of a Jacuzzi is:
Home mini SPA: Once upon a time, hydromassage baths were only available in expensive SPA salons. Now you can enjoy the magical hydromassage of water air jets, relaxing and relieving stress, right at home.
Therapeutic effect: Jacuzzi hydromassage stimulates blood circulation, improves metabolism and cleanses the body of toxins. Installing a Jacuzzi also helps preserve beauty; in particular, such a bathtub fights fat deposits and cellulite in women.
Relaxation and toning: Warm circulating water perfectly relaxes, and underwater water jets provide acupressure, after which you feel invigorated and rested.
Finally, a bubble bath is an opportunity to have incredible fun every day. Order your Jacuzzi installation from us right now! List of works performed during the installation of products from the Jacuzzi Europe SpA factory
- Checking the readiness of the site for installation of the product.
- Checking the product contents.
- Installation of the product on the prepared site.
- Connection of power supply, cold and hot water, sewerage.
- Electronic and hydraulic system testing.
- Technical inspection of functional units and assemblies of the product.
- Demonstration of the operation of all product functions and training in the rules of use.
- Conducting safety training when operating the product.
- Filling out the manufacturer's warranty card indicating the warranty periods.
Warranties Jacuzzi products installed by specialists and the work carried out are covered by a 1-year warranty from the date of installation. For products whose production date differs from the installation date by 2 years or more, the warranty period is determined by the condition of the product during installation. Products of the J-Sha and Morphosis series, mini-pools installed by specialists and work performed are covered by a 1-year warranty from the date of installation. For products whose production date differs from the installation date by 2 years or more, the warranty period is determined by the condition of the product at the time of installation.
Self-installation of a jacuzzi
If you decide that you can install a hot tub yourself, then you need to familiarize yourself with more detailed installation instructions and perform them in the same way as those recommended above.
Detailed instructions include the following points:
- In the accompanying documents, find a section that describes how to install a hot tub. Find out whether the manufacturer recommends sealing the sides of the bathroom and what materials are best for doing this. Prepare them and proceed directly to installation.
- Check out the set of parts for installing a bathroom: spacer dowels, support brackets, screws, washers - there should be 4 of them.
- Place the bathtub in the place it is intended for, adjust the legs until the sides are horizontal, check the level, checking the horizontalness along the sides and across.
- Make sure there is room for the decorative panel, if provided, install fasteners for the panel.
- Draw a line on the bathroom wall along the expected line of the edges.
- Mark the places where the brackets will be installed under the line at a distance of 6 cm. The location of these points should be uniform relative to the sides of the bath.
- At the marked points, attach the brackets that will support the bath. Use the dowels and screws from the kit for this.
- Carefully install the hot tub by hooking the sides onto the brackets.
- Connect the siphon to the sewer using a hydraulic seal and a fairly long corrugated tube, which must be purchased additionally. The ability to maneuver the bathroom depends on the length.
- Install decorative panels.
- To seal the joints between the sides and the walls, treat the joints with silicone sealant.
The electrical connection is described above, but if you are not an electrician, then invite a specialist to check the possibility of connecting the equipment, this will be the best option for safety.
If you want to cover the space under the bathtub with a decorative panel, then between it and the floor, you need to leave a distance of 20-30 mm, necessary for the ventilation that hydromassage equipment needs.
The installation of the front and side decorative panels must be done in the correct order; first install the side panel, then the front panel.
Many Jacuzzi manufacturers recommend using decorative panels for aesthetics and do not recommend covering the space with tiles, because the panels are easier to dismantle when repairing hydromassage equipment. Using all these recommendations and tips, you can install a jacuzzi at home and use it for beauty and health.
Right choice
When choosing a Jacuzzi, you need to be guided not only by personal preferences. If you are going to install it yourself, then an important point is to study the instructions. A high-quality and conscientious manufacturer always indicates a complete list of requirements that must be observed during installation. Step-by-step recommendations are included in the installation sheet, which must be included with each model.
In addition, the choice is influenced by the size of the bathroom. The Jacuzzi should, if necessary, be accessible for easy and uncomplicated repairs. Take measurements in advance not only of the bathroom itself, but also of the doorway so that you can bring in the Jacuzzi without any problems. Thanks to these simple steps, in the store you will immediately refuse to consider models that are a priori not suitable for your premises. An equally important criterion is the weight of the empty and filled whirlpool bath; a whirlpool puts a serious load on the floor.
When choosing a bathtub, consider the material from which the hot tub is made. Today, the most common and practical is acrylic.
Step-by-step instructions on how to install a bathtub
Stage 1 - installation of the reducer and filters for the bathroom. A standard hot tub is designed for a water pressure of 4-5 atm, so to avoid exceeding this figure, it is recommended to install a pressure reducer. Special filters will ensure the purification of water, the quality of which in taps leaves much to be desired. It is advisable to install a multi-stage filter system - this will avoid rapid clogging of the nozzles, and therefore will extend the overall service life of the entire product.
Filters for water purification
Stage 2 - height adjustment. Before connecting the bathtub to the sewer, it is carefully placed on its legs in a pre-selected and properly prepared place, the height is leveled using adjusting bolts. It is not necessary to place it strictly horizontally; a small angle of inclination to the drain is acceptable.
Adjusting the bath level
Stage 3 - installation of the drainage system. The drain should be located above the main drainage system at a distance of about 10 cm. In general, connecting the bathtub to the sewer is done in exactly the same way as a regular bathtub, the only difference is that all seams and joints must be sealed. The drain-overflow system is semi-automatic; for installation, it is enough to connect the hose that comes from the holes to the general drain system using special fittings.
Connecting a bathtub to a sewer system with a drain-overflow system
Stage 4 - installing a faucet in the bathroom. Mixer taps are mounted quite simply, and not on an adjacent wall, as is usually the case for conventional bathtubs, but directly to the jacuzzi itself.
Stage 5 - connecting to the power grid
The first and most important rule to remember: the work site must be de-energized! The Jacuzzi is connected to the system using a three-wire cable, the socket is grounded and installed outside the bathroom or at least 1 meter away from the hydromassage installation. The socket is connected to the panel via a circuit breaker and an individual RCD
When connecting the wires of an electrical cable, you should be extremely careful that the zero of the cable is connected to the neutral wire (blue color of the wire), the phase - to the phase of the device (marked in white, brown or red), and the ground - accordingly, to the ground (yellow-green color of the cable) ). All parts of the bathroom that come into contact with electric current must be placed in waterproof boxes.
Attention! Follow safety rules! Turn off the electrical switch! It is recommended to entrust the work to a qualified technician if you do not have special skills in connecting devices to the electrical network. Stage 6 - installing a decorative screen
Usually the screen comes included, but you can make it yourself. The main rule that should not be forgotten is that whatever the screen, it should always provide quick and easy access to all connections
Stage 6 - a decorative screen is installed. Usually the screen comes included, but you can make it yourself. The main rule that should not be forgotten is that whatever the screen, it should always provide quick and easy access to all connections.
spa screen
Stage 7 - launch to check functionality. It is necessary to make sure that the filters, pressure reducer, RCD are installed correctly, there is free access to the system, the structure is stable in place, the drain is sealed, and there are no leaks at the pipe connections. After checking the electrical insulation, you can make the first start and enjoy swimming.
A very interesting and detailed video on installing a bathtub!
Features of installation work
Before installing a Jacuzzi in the room, it is necessary to completely complete the repair work on the walls, ceiling, and floor. The pipes of the water supply system must be equipped with filters in advance; when using well water, it will be necessary to install filters that carry out mechanical cleaning. Bathroom sockets must be equipped with a grounding system, connected using an RCD, and have a protection level of at least four. If there are no electrical outlets in the room, the jacuzzi is connected to the electrical network using a cable that stretches across the entire room.
How to install a Jacuzzi body
The hole for draining the water should be ten centimeters from the floor level; sometimes it is necessary to use a special stand.
Connection of pipes with sewerage, water supply system
The water supply pressure should not exceed five. To control the pressure, it is better to install a special reducer. Water from the central sewer has many impurities, and well water even more so. It is necessary to prepare filters for thorough cleaning in advance. The pipes should run close to the bathtub, without blocking the approach to the connecting corners.
The diameter of the drain into the sewer is approximately five centimeters. The process of installing faucets and connecting them to water pipes is the same as for a standard bath. The faucet is installed inside the bathtub bowl. The Jacuzzi has a modern semi-automatic drainage system with overflow. There is a handle on the overflow hole that opens the overflow valve. The bathtub is connected to the sewer with a flexible hose; it should have a length of approximately fifty centimeters.
All connections must be equipped with rubber gaskets against leaks.
The sewer system pipe can come out of the wall or floor, but no more than two centimeters from the floor. The siphon is connected to the drain using a corrugated pipe.
Next, install the Jacuzzi bowl. At the end of the work, inspect the joints and connections again.
Recommendations for use
To ensure that your bath lasts a long time and the procedures are truly beneficial, follow these rules:
- Do not turn on the pump and the light, if any, if there is no water in the bath - this will lead to overheating of this equipment.
- Foaming detergents cannot be used when bathing, but various aromatic essences that do not produce foam can be used.
At least once every 2 months (preferably monthly), the Jacuzzi equipment must be disinfected. A composition specially designed for this purpose (sold in any store) must be poured into a filled bath in the amount specified by the manufacturer, then for about 2 minutes. Activate hydromassage mode. Then the equipment must be rinsed with cold water using the same mode.
Bidets are not often seen in bathrooms, but there is no doubt about the usefulness of bidets. Bidet lid – functions, advantages and disadvantages, as well as reviews of use, read on our website.
Are you looking for an inexpensive option for finishing your bathroom ceiling? A bathroom ceiling made of plastic panels is a simple and durable option. Read on for installation methods.
Installing a hot tub is not easy
Installation of a jacuzzi begins with a preparatory period, which consists of several stages:
- It is necessary to measure the dimensions of the room where the hydromassage equipment will operate. The requirements for the bathroom are quite specific and their compliance is necessary, since a bathtub with internal filling is a heavy object, and the vibrations that occur during operation affect the floors. Therefore, the floors must be reinforced concrete, and the ceilings must be up to 3 meters high for normal functioning, ventilation and therapeutic effects.
- The location of the pipes is of great importance; the supply pipes should not rest against the ribs of the bathroom so as not to interfere with the operation of the equipment, and the drain hole should be in the floor or at a height of no more than 3 cm from the floor.
- Then the old plumbing equipment is dismantled.
- The sewer pipes are being replaced and the water supply system in the apartment is being updated.
- The floors are leveled and waterproofed.
Required Tools
First we need to decide on the tools that we will need when installing the structure:
- building level - to set an even horizon for the sides of the font;
- hammer drill - for drilling holes in the wall in order to secure the font on additional supports;
- a set of keys - for assembling the frame and adjusting the legs;
- tape measure - for measurements;
- screwdriver - for assembling frame elements and attaching them to the bowl;
- side cutters - for electrical installation;
- multimeter - for checking electrical circuits;
- construction marker - for marking.
Jacuzzis are different
In the world of plumbing, hydromassage baths come in all their variety.
Which modification of the bathtub to choose is dictated by both the shape and dimensions of the room in which it will be installed. It is better not to install bathtubs with hydromassage instead of a regular bathtub; its use in an apartment building is not recommended.
Attention! Before installing the jacuzzi, they make a detailed plan of the room where it will be installed. The plan indicates the parameters of the room, notes the outlets for electricity and water supply.
The choice of plumbing fixtures depends on the data obtained.
Jacuzzis are distinguished by a variety of surface coatings:
- 1.baths made of cast iron.
- 2.baths made of acrylic.
- 3.baths made of steel.
- 4.baths made of stone.
Steel and acrylic bowls are lighter and can be installed in apartment bathrooms. If the floor can support a structure weighing more than a ton, then the installation of cast iron and stone models is allowed. Jacuzzis made of stone and enamel materials are resistant to chemicals, withstand heavy loads, and retain their original appearance regardless of weight.
Hot tubs operate without loud noise and keep the water warm for a long time.
In everyday life, bathtubs made of acrylic material are common, the composition of which is durable and light at the same time; models have different color variations and differ in shape. Scratches that occur during use of the bathtub can be polished out.
Bowl shape
Jacuzzis come in a variety of shapes. They are:
- -round shape
- -oval shape
- - rectangular shape
- -square shape
- -in the shape of an angle
- -non-standard shape
In a room with small dimensions, rectangular or corner bathtubs are recommended. Models in the form of a circle or oval are usually installed in the center of the room. They require a lot of space.
Square-type models or non-standard bathtubs are mounted under the walls.
Instructions for installing a hot tub
When installing a hot tub, it is important to pay attention to the following key points:
- Sewerage. The water is drained using a standard plastic pipe with a diameter of 5 cm. It is better to make the drain hole in the corner. Exiting the sewer pipe from the wall is allowed if the distance between the lowest point and the floor is no more than 5 cm.
- Water quality. The installation of a hydromassage bath must be accompanied by the installation of a mechanical coarse water filter. In addition to this, it is advisable to install a fine filter. If the water is very hard and contains a high iron content, it is necessary to install a special unit that softens the water and removes excess iron.
- Electrical connection. It is not recommended to connect the Jacuzzi to an outlet located in the bathroom. It should be connected using a solid cable to the house distribution board. Mandatory points are the installation of an emergency shutdown device and an autonomous circuit breaker. When connecting, use a copper cable with three cores (phase conductor, neutral and protective wires) and double polyvinyl chloride insulation. Hot tub equipment consumes approximately 1.9-3.5 kW of electricity. This means that the cross-sections of the cable conductors should be 1.5-3 square meters. mm.
- Ventilation and leveling. Hydromassage products are installed exclusively horizontally, level. Even a small deviation can have unpleasant consequences. The bathtub is leveled using screw feet, on which the product itself stands. If necessary, additional supports can be installed.
The sides of the whirlpool bathtub are covered with decorative panels or tiled decorative walls. In the first option, you need to leave a small gap of about 3 cm between the floor and the panel. This is necessary to ensure heat and ventilation of the equipment - pump, fan, control unit, which are located under the bowl. In the second case, a pair of small ventilation hatches should be located in the wall. Part of it is made voluminous so that it is possible to access the equipment for its repair and prevention or cleaning of debris accumulated under the bathtub.
As can be seen from the information above, in order to properly install a whirlpool bath yourself, you need to understand this. In the absence of at least some knowledge and skills, it is better to entrust the installation to specialists. After all, the life and quality of operation of an expensive bathtub directly depends on high-quality installation.
Features of hydromassage baths
A Jacuzzi is a technologically complex piece of equipment. The connection occurs not only to the water supply and sewerage, but also to the electrical network, which is necessary for the operation of pumps and compressors. The following characteristics must be taken into account:
- Size. It completely depends on the dimensions of the room. It must be installed at a certain distance from the wall.
- Power. The pressure of the water jets directly depends on the power of the compressor. It can fluctuate in the range of 800-1500 W.
- Type and number of nozzles. Some of them may have several hydromassage modes.
- Additional options: automatic heating, lighting, audio system, built-in aromatherapy system.
How to connect a jacuzzi to power supply
When connecting a hot tub, you must have a network with a voltage of two hundred and twenty volts, a cable with three cores of the required length, and an RCD. You also need to prepare a grounding system, a switch, a voltage stabilization device, and electrical wires with a diameter of 3 millimeters or more.
Checking the proper operation of the jacuzzi
To check the quality of operation, the Jacuzzi is filled with water until all nozzles are immersed. Connect to the mains and check all built-in functions. To drain the water, the Jacuzzi is turned off. The operation of the injectors is controlled using the system control panel.
After carefully checking the correct electrical connections, the legs are attached to the floor, and the cracks with the wall are sealed with sealant.
What is the difference between installing an outdoor Jacuzzi? Fashion that came from Europe dictates the installation of a jacuzzi on verandas or near the house. Abroad, you need special permission to install a bathtub on the street.
At the stage of choosing a suitable place to install a jacuzzi, you need to know that the bathtub should be located at a distance of one and a half meters or more from the house and the fence of the site. The distance to power lines running along the top should be more than three meters.
How to prepare a place for a jacuzzi. First of all, they build a reliable foundation for the bathtub, since due to the large volume of water, its weight can reach more than a ton. A cast concrete base is considered reliable and is therefore a common method. Concrete is laid in a layer of up to 11 centimeters; this choice will make it difficult to move the Jacuzzi to another place.
A foundation made of slabs and a prefabricated structure will simplify installation and dismantling work. The strength of the panels must correspond to the size of the jacuzzi. Before installing a jacuzzi on a terrace, you need to make sure that the flooring can support its weight.
Electrical connection
Cable laying can be above ground or underground. The cable cross-section is selected depending on the distance of the disconnector in relation to the bath. Copper cable with nylon insulation system is suitable.
This is followed by the installation of an RCD with a voltage of two hundred and forty volts, with a 50 A circuit; models with a multi-level pump require a 60 A circuit. The unit for controlling electricity is equipped with a disconnector. No other electrical appliances should be connected to the Jacuzzi circuit.
Many models do not need to be connected to the water supply system; water is drawn into it using a hose and then heated.
Panels are sold along with the jacuzzi to close the lower space, leaving a gap of three centimeters to ensure ventilation.
Important! Do not lay tiles along the edge of the hot tub. If the structure needs to be dismantled, the edges of the bathtub will be damaged.
How to properly start a jacuzzi. You can turn on the Jacuzzi only after filling the bowl with water. Existing nozzles are completely covered with water to prevent pump overheating and damage. At this stage, the pressure of the water outlet from the nozzles is adjusted.
Water can be heated to fifty degrees, and aromatic oils and non-foaming cleaning agents can be used.
Preliminary work
Wiring diagram for a hot tub.
Before purchasing a hot tub, you should measure the room. Based on these indicators, you need to choose it. Moreover, the minimum size of the room should be the size of the bath itself and another 1 meter on each side. This addition will make it possible to have free access to the area under the bathroom. It is also necessary to take into account that hydromassage baths are most often installed in rooms with high ceilings. The product is heavy, so its installation is recommended only in houses with reinforced concrete floors
It is important to take into account the dimensions of the doorway - the bathtub should pass freely
Before you begin installing the product, you should prepare the bathroom. The pipes also need to be replaced. If necessary, the floor is leveled and waterproofed.
Thermal spring within the walls of the house
Hydrotherapy is a common method of relaxation and healing that has been actively practiced since the 1st century BC. Its medicinal properties are mentioned in the Indian Vedas.
The first hydromassage bath in our usual sense appeared in Berlin in the mid-30s of the last century.
Thanks to the skill of one of the Jacuzzi brothers, the system was supplemented with a pump that ejects a powerful jet with many air bubbles, and numerous nozzles from which streams called “thousand fingers” erupted.
Types of baths according to massage equipment
The baths are equipped with different types of massage. There are Jacuzzis with water massage, with air massage, equipped with water-air massage, ultrasonic, even pulsating or sinusoidal massage. Modern Jacuzzis use a water-air type of massage, when a stream of water and air under strong pressure emerges from micro-holes in the walls of the bathtub. Water supply nozzles are usually located in the lumbar area, at hip level, on the side of the bathtub and along the back. The water supply from the nozzles can be adjusted: either all at the same time, or one by one. The latest modifications are equipped with built-in programs for setting the start time of each nozzle and controlling the feed force.
Modern equipment for a hot tub
The type of bathtub can be selected based on the availability of additional functions. Jacuzzis have additional design elements: headrests, auxiliary steps and handles. Jacuzzis are equipped with color and aroma therapy functions, have the function of a music and TV receiver, can carry out offline disinfection, and have additional mixers.
Structural elements that a Jacuzzi is equipped with
To assemble a hot tub with your own hands, you need to understand what is included in the technical assembly kit. This is a pump pumping water, nozzles for releasing streams, a compressor, electronic or pneumatic control with built-in functions, and pipes. Using a pump, water is supplied to a compressor mechanism in which air is combined with water. Water flows into the container with pressure through the nozzles.
The massage type of bath varies depending on the structure and number of nozzles. The pipes coming from the bathtub are built into sewer and drainage pipes. A large number of injectors requires a pump with higher power.
