We make roller shears ourselves from bearings

Roller shears and sheet metal cutting features

In the metalworking industry, roller shears or knives are used to process sheet material. This tool is called knives because its operation is based on the use of two cutting discs. The cutting process is based on the fact that rollers are pressed into the sheet material from two sides - top and bottom. In this case, it is cut without the use of any sharp knives. The role of cutting and sharp knives is played by rollers, which touch the walls to each other on both sides.

Rollers not only cut sheet material, but also facilitate the process of moving the tool along the surface of the sheet. This means that cutting with a roller knife is not only convenient, but also effective. If we compare the operation of the device with hand scissors, the following advantages should be noted:

• Speed ​​- cutting a sheet of steel with roller shears can be done in a matter of seconds, but using scissors requires a lot of time, which depends on the length of the material being cut
• Cut quality - the roller knife cuts not only quickly, but also with high quality. There are no chips, bends, bends, etc. at the site of the cut
• Physical fatigue - cutting with hand scissors requires physical effort, while using a roller tool eliminates this need. To cut, you only need to move the roller shears along the guides, thereby cutting the steel sheet

Roller shears are classified according to the types of knives into three types:

1. They are located in parallel. The most popular type of cutting tool, which is intended exclusively for cutting material into strips, that is, cutting is performed in a straight direction
2. They have one slope. They are intended for cutting not only even strips of sheet material, but also for cutting round and ring-type workpieces
3. With several slopes. Such roller devices are intended directly for cutting workpieces of various shapes - ring, round, curved, etc.

After cutting, the edge of the material does not need additional processing, as it turns out smooth, without chips or burrs.

How to cut sheet metal at home

In industry, roller shears are used to cut factory-produced sheet metal. Their distinctive features are high accuracy, long service life, and the absence of the need to make them yourself. Often in the household there is a need to obtain even strips of sheet steel, which are used for various purposes. If you need one strip, then there is no need to buy or make such a device, since you can use ordinary metal scissors. If you need to cut the entire sheet or carry out cutting work regularly, then it is imperative to acquire a roller knife.

There is no justifiable sense in buying such a factory-made device, since the price ranges from 15 thousand rubles or more, which depends on the design, size and quality of the device. Roller shears for cutting sheet metal can be made with your own hands at home, using available consumables for manufacturing. Although this method requires time, it allows you to save money, resulting in a universal cutting tool for cutting sheets of stainless steel, galvanized steel, etc.

This is interesting!
It should be noted that roller shears are only suitable for cutting flat sheets, and they cannot be used to cut sheets with protrusions and recesses, for example, corrugated sheets in the transverse direction.

Manufacturing instructions

Factory models of cutters sold in stores, even in standard configuration, will cost a large amount. The price of models offered on the market starts from 20,000 rubles. Such conditions are not beneficial for purchasing a tool for home use or a small workshop, and it will be used extremely rarely.

To begin with, the main body of the instrument is designed, which everyone chooses for themselves. The main attribute of the machine is manufactured - a roller knife for sheet metal. The material from which the part is made directly affects the durability and performance of the unit. As mentioned above, the strength characteristics should be significantly higher than the similar characteristics of the material being cut. Otherwise, the minimum problem will be a low-quality cut, forcing the craftsman to clean and process the edges of each cut piece.

Scheme for assembling a roller knife

Do-it-yourself roller metal shears are mostly made from bearings. Sharpening the ends of the part forms the cutting surfaces. The main roller, connected to the drive, is attached directly to the handle. The lower one is installed on the fixed lower part of the machine. If you have skills in processing iron alloys, manufacturing such a device will take a maximum of a little more than a week, including setting up the unit.

Features of making a tool yourself

If you are tired of cutting sheet metal with scissors or a grinder, then a roller cutter is an excellent alternative to replace these tools. The advantages of this device include quiet operation and lack of energy consumption. In addition, having such a device in your home arsenal, you can even make money when your neighbors need to cut sheet metal material.

The purchase of a tool is justified only in one case, when it is necessary to perform work in large quantities. And even in this case, you can make the device yourself to use it for professional purposes. There are many designs for the devices in question, so making a device yourself is not at all difficult if you understand the principle of operation of the device.

When making a homemade tool, the following properties must be taken into account:

1. Cutting knives - there should be two of them, one located on top and the other on the bottom. Knives must be made of high-quality alloy, which has a strength higher than the materials being cut. Bearings that fully meet the described requirements are used as knives.
2. Base - simultaneously acts as a surface on which the steel sheet is located, as well as a guide for moving the roller shears when cutting the sheet or cutting strips
3. Body of the device - for manufacturing, a steel angle with a thickness of 3 mm and a wall size of 40-60 mm is usually used
4. Auxiliary tools - they are designed to secure the sheet material to the table surface while cutting it

This is interesting!
The service life of homemade roller knives is quite high, and is almost equal to that of factory models.
The service life of factory devices is at least 25 km, but provided that the thickness of the cut steel does not exceed 0.5 mm. The thicker the steel, the shorter the service life of the tool. The service life of a homemade device is influenced by such an indicator as the quality of its manufacture. Moreover, this even applies to the quality of bearings, so if you get down to business, you will need an appropriate approach.

Maintenance and operation

The main routine maintenance of the equipment consists of periodic sharpening of the tooling (during first use, simply turn the knives 180°). Sharpening can be done on a grinding machine using a carborundum wheel, after which it is necessary to grind the resulting surface. After repeated regrinding, the stability of the gap must be maintained by installing steel gaskets. Their thickness is determined experimentally.

Periodically check the gaps in the joints and lubricate them with Industrial-20 oil or similar.

When manufacturing equipment, it is strictly not recommended to settle on the sector version, which will require welding. The accuracy of metal cutting will inevitably deteriorate.

To improve the reliability of mounting desktop hand scissors with a lever mechanism on a workbench, it should be reinforced on the opposite side using a steel angle, channel or thick strip.

What to make a roller knife from

There are no difficulties with purchasing roller shears, since such a machine can be found in an online store and ordered. The only difficulty is that you will have to shell out a considerable amount of money to purchase it, which will not pay off soon if you do not use such equipment often. Making your own will not require any costs, but the biggest difficulty is choosing the necessary materials and assembling full-fledged roller shears from them.

Using a homemade machine allows you to cut the following types of materials:

• Cink Steel
• Stainless steel
• Aluminum
• Steel sheets up to 0.5 mm thick, for example, window slopes of metal-plastic windows

Bearings are used to make cutting knives. The diameter of these bearings depends on the size of the roller blade housing, but 20-30mm ball bearings are commonly used. In order for the bearings to ensure cutting of material, it is necessary to grind off their end faces, making them strictly at an angle of 90 degrees. The effectiveness of the tool depends on this.

This is interesting!
The diameter of the bearings affects the cutting speed. The larger the size of the bearings, the correspondingly higher the cutting speed.

Before you make a roller-type cutting tool, you need to understand its principle of use. The application is based on the fact that a homemade knife moves along guides. The corner part of a workbench or table is used as such guides. The sheet to be cut is placed on the surface of the table, and in order for the cut to be smooth and neat, it should be fixed in a stationary position. This can be done using two clamps and a wooden block of appropriate length. A block is placed on the sheet, and then it is fixed on both sides with clamps, thereby ensuring immobility during processing.

Rules for working with lever shears

Before starting work, you must put on seals so as not to get cut by the sharp edges of the metal sheet!

• Firmly fix the hand tool on the table surface;
• place the sheet of metal perpendicular to the blades, holding it with your main hand (right hand for right-handers);
• Smoothly and carefully press the handle from top to bottom.

While working, you need to protect your feet from falling pieces of cut metal. Falls on the edge are especially dangerous, so you should not work barefoot or in open shoes. To install the scissors, choose only a solid, non-wobbly base.

Instructions on how to make roller shears from bearings with your own hands

As already mentioned, there are many options for making a homemade roller cutting tool, but which one to choose for yourself depends not only on the capabilities, but also on the availability of the necessary consumables. If you need a simple homemade roller knife, you can make it from bearings. The manufacturing principle is simple, and first let’s figure out what tools and materials will be needed to make it:

1. Two bearings 204 or 205. You can use other bearings that are available. They don't have to be the same size
2. Corner 50-60 mm up to 30 cm long
3. Threaded connectors, washers, nuts and other small consumables
4. Steel tube from which to make a handle for roller shears
5. The tools you will need are a welding machine, as well as a drill and grinder

When all the necessary materials are ready for work, you can get down to business. Instructions for making a roller knife yourself are as follows:

1. First you need to prepare a corner, since it will act as a body on which additional elements will be placed
2. We grind the edge of the bearings. Moreover, this must be done in such a way that the resulting edge has an acute angle. On both bearings it is necessary to “remove” the edge, since the possibility of using the roller shears for their intended purpose depends on this
3. Next, you need to drill a hole in the corner and attach one bearing to it. A bolt with a countersunk head is used for fastening. A washer is also used to secure the bearing, which will ensure reliable pressure against the wall of the angle
   Read also:  Sealing machine: design, do-it-yourself manufacturing, drawings
4. The bearing is attached so that its outer race protrudes 1-2 mm from above the edge of the angle. It is important to provide for the possibility of adjusting its contact with the second bearing by placing washers on the inside
5. On the reverse side, when securing the bearing, it is necessary to ensure that the head of the fastening bolt is recessed into the base of the angle. This is necessary so that the homemade tool can move freely along the edge of the workbench. If you can’t drown the hat, you can make a groove for it in the workbench design, which is also quite appropriate when using homemade scissors

6. The first part of the work at this stage is considered completed, so you should proceed to the manufacture of the second part. This is the handle, the second bearing, and also the sheet bender
7. Using a similar corner that is 2 times shorter in length, you need to attach the second bearing to it. First, using a grinder, you need to cut the corner into the shape shown in the photo below.

8. It is necessary to attach the bearing to the end part of the resulting workpiece by first drilling a hole

9. Weld the corner piece to the main part as shown in the photo. It is important to take into account that the upper bearing must be in close contact with the lower bearing, and its outer race must be located at a distance of up to 1 mm from the base of the angle

10. Finally, you need to attach the handle to the resulting installation so that it is convenient to work

The result is a homemade cutting tool for cutting metal sheets up to 0.5 mm thick. When using the device, it must be taken into account that it is intended exclusively for working with sheet materials. During operation, the edge of the bearings will wear out, so it is advisable to provide during manufacturing the possibility of adjusting the contact of the bearings. All the details of the manufacture and use of such a tool are in the video below.

This is interesting!
When you rotate one bearing by hand, the second should also rotate, which indicates that the homemade product was manufactured correctly.
The greater the distance between the end parts of the bearings, the lower the quality of the tool. In conclusion, as an example, it is worth giving an example of how much a factory roller blade costs, as well as what technical parameters it has. For example, consider a Trim Cutter 3017 brand machine and its technical parameters:

• Maximum sheet metal thickness - 0.7 mm
• The weight of the device is 4 kg
• Overall dimensions - 220x180x260 mm
• Cost from 25,000 rubles

Based on the above, it can be noted that making roller shears for cutting thin sheet metal with your own hands is not at all difficult. This does not require a lot of effort and consumables. With just 3-4 hours of free time, you can make a highly effective cutting tool at home. With roller shears, you don’t need to think about how to cut a metal sheet when installing window slopes or how to cut galvanized sheets into strips, since with it any similar work is carried out easily, quickly and efficiently.

Three-link lever shears

It has been established that the scheme, which will be described below, can cut long and sheet metal with a cross-sectional size of up to 10 mm, which in most cases is sufficient not only for one’s own needs, but also for the manufacture of steel products in a small business.

These scissors consist of the following components:

1. A frame, for the manufacture of which you will need two equal-sized corners with a shelf thickness of at least 7 mm.
2. The lower support to which the working tool is attached.
3. The upper support, which is installed in the seat, and has a bevel in order to reduce the gap between the knives at the moment the cutting begins.
4. The housings in which the mounting holes for the knives should be made slightly oval in shape to compensate for possible errors in the installation of the tool.
5. Earrings.
6. Connecting axis.
7. Fasteners.

For the manufacture of all parts of the multi-link mechanism, medium alloy steel grade 35 or higher will be required.

The length of the support frame is determined by the maximum dimensions of the metal being cut: the size of hand shears will be approximately twice the width of the workpiece. However, the design turns out to be quite compact, and allows you to use a regular bench vice and a workbench of appropriate size for installation.

The working tool attachment scheme is as follows. In the equipment made from high-strength tool steel grades U10 or U12, mounting holes are made with a countersunk conical part so that the fastening is flush-mounted. The kit should include options for cutting profiled metal. To facilitate maintenance, the equipment should be made double-sided. Next, heat treatment is carried out to a hardness of at least 54...56 HRC, and grinding is carried out in order to eliminate possible warping of the working blade. The finished equipment is installed in the lower and upper landing parts, and is adjusted one after the other in such a way that the actual gap between the moving and stationary parts does not exceed 5...8% of the thickness of the metal being cut.